Sanitary Ware Installation Process

By:


First, construction preparation
1. Material requirements
1) Sanitary specifications, models must meet the design requirements; and a factory product certification. Sanitary appearance should be rules, modeling Zhou Zheng, smooth and beautiful, no cracks, edges smooth, consistent tone.
2) Sanitary parts specifications should be the standard, quality, reliability, appearance smooth, uniform plating, clear thread, lock master moderately elastic, no blisters, cracks and other defects.
3) sanitary ware water tank should be saving.
4) Other materials: galvanized pipe fittings, leather money valve, character valves, faucets, water bend threaded back, drain, galvanized dovetail bolts, nuts, rubber sheet, copper wire, putty, lead sheet, screw , solder, cooked hydrochloric acid, lead and oil, flax, asbestos rope, white cement, mortar ointment should meet the material standards.

2. The main equipment
1) equipment: sets of silk machine, grinding machine, wheel saws, electric drill, impact drill.
2) tools: pipe pliers, handsaw, iron, fabric scissors, live wrench, home-made die wrench, cross wrench, hand hammer, hand shovel, chisel, Cutting pliers, square file, round file, screwdriver, soldering iron and so on.
3) other; Level, planning regulations, line sinkers, a small line, box foot, etc..

3. Working conditions
1) All sanitary pipes connected with the pressure, closed water test has been completed and pre-screening process to run hidden.
2) the stability of tub installation should be done civil engineering waterproofing layer and protective layer with the civil construction carried out after.
3) other sanitary ware should be basically completed in the interior decoration for stability after installation.

Second, the operation process
1. Process
Installation of sanitary ware and accessories ready test install sanitary ware sanitary fittings sanitary ware preinstalled stability sanitary ware fitted with wall and crevice treatment through sanitary inspection of the exterior water test

2. Sanitary ware in the stability check before installation, cleaning. Accessories and sanitary ware should be supporting. Part of the sanitary ware should be prefabricated and then installed.

Third, product protection
1. Wares in the handling and installation to prevent knock. Stable outfall sanitary ware application installed protective equipment after the block is good, a good chrome parts wrapped in paper to prevent blockage or damage.
2. In glazed tiles, terrazzo wall holes tick when it is appropriate to first use a small electric drill or chisel out glazed light tick, tick to wait until the end brick prescription ash layer can be hard, but not excessive, to avoid breaking the surface layer of tick or shock into the phenomenon of hollowing.
3. Sanitary stable equipment, in order to prevent loss or damage parts such as zipper, blocking chain material, accessories shall be installed before the completion of unification.
4. Installation of sanitary ware should be protected against damage and the sanitary ware porcelain surface damage.
5. Through the water to drain should be checked before the test is smooth, splitting the valve is properly closed, and then divided by layers of water testing through the room one by one in order to avoid water leakage damage to decoration.
6. In the winter, warm interior barrier, the variety of wares must put the water net. Traps should be no stagnant water will be sanitary and trap the cracking.

Fourth, the quality of attention
1. Squatting pan injustice, right and left tilt. Reason: stable installation, the front and sides of pads brick is not strong, cinder fill, no checks, after the bad plaster repair, resulting in high water tank and toilet misalignment.
2. High and low water tank pull, pull into the terminal. Reasons: the high and low parts installed inside the water tank, the three main components in the tank position is unreasonable. High tank water, pull the tank should be placed on the same side. Used to avoid interference. Sina Music Home Forum
3. Parts chrome surface is damaged. Cause: The installation using the pipe wrench. Should be made flat spanner or wrench.
4. Toilet tank center and back is not right, elbow contorted. Reason: crossed misalignment, improper installation or the first toilet stable steady back box, after the steady toilet.
5. Toilet around off the ground. Reason: I set aside under the water too high, stability did not repair before installation.
6. Urinal from the wall of vertical cracks too. Reason: rejection port size is not accurate.
7. Sanitary overflow failure. Reason: Xia Shuikou no overflow eyes.
8. Through the water until the dirt within the apparatus to clean up, not be allowed to pass into the dirt under the water pipes within Pianqiang avoid pipe blockage. Do not use unfiltered white lime mortar powder instead of paste installation of sanitary equipment, sanitary equipment Splitting avoid




About the Author:
Yuyao Huaneng sanitary ware factory is specialized in production of plumbing fittings. 'Aige' sanitary ware series are well received not only by supporting factories but also customers both at home and abroad. The products are well sold at home and exported to the world as well.



Article Originally Published On: http://www.articlesnatch.com


|

Loading...
Related....
Videos...

Recent Business Articles

Comments

Still can't find what you are looking for? Search for it!

Loading

Copyright 2005-2011 ArticleSnatch, LLC - All Rights Reserved.
Privacy Policy | Terms of Service.