How To Build Deck Stairs?

How To Build Deck Stairs?

By:


Making deck steps is not hard to do. Anyone with basic construction knowledge or a healthy sense of fun can make a solid and attractive set without leaning into too many problems. This guide provides information on how to construct deck steps yourself to save on the fee for a contractor.

Preparation for design and construction:

The Total Run is the total horizontal length covered by the staircase, from the edge of the deck to the edge of the staircase
The Total Rise is the total vertical length from the surface of the landing to a point level with the surface of the upper floor
Run is the horizontal length from the leading edge of one tread to the leading edge of the following tread.
Rise is the vertical distance from the surface of one tread to the surface of the following tread.

The ratio of the total rise to total run determines the slope of the staircase. This might constantly fall in the range of 30 and 35 degrees. Typical riser height is around 7" with an 11" run (standard lumber stock breadth)

The breadth of the stairway may be around 48 to hold one individual and roughly 60 for two.

Stairways are made of four parts:
1) Stringers - inclined members that reinforce the stairway usually created from 2x10s with no large knots that are created from redwood or cedar, to resist decay.
2) Treads - horizontal planks that you walk on. When building deck steps they are constructed from similar material as the deck.
3) Risers - vertical planks behind every tread.
4) Railing - built from posts, a cap rail and vertical balusters between each post. 4x4 is the most familiar post material with a 2x4 handrail.

Planning the deck stairs

Determine the total rise and divide the figure by 7 to obtain the number of steps you will require. If the result is a fraction round off to the nearest whole number

Divide the entire rise by the resulting whole number to determine the height of each riser.

Constructing the deck steps

Step one: find the entire rise and divide the figure by 7 to get how many steps you will need. If the result is a fraction round off to the nearest whole number

Divide the total rise by the resulting whole number to determine the height of each riser

Building the deck stairs:

Required Tools/ Materials
2x10 Stringers
5/4" or 2" Tread Material
Angle Iron
Hex Bolts
8d Galvanized Nails
Hammer
Measuring Tape
Joist Hangers
1x8 Risers
2x6 Pressure-Treated Cleat
Anchor Bolts
16d Galvanized Nails
Baluster Material
Carpenter's Square
Adjustable Wrench

Instruction

Step one:
Notch the stringers for the treads and risers. Fasten two stair gauges to a carpenter's square to the specifications of the rise and run you have calculated (for instance, set the square on the stringer so the gauges are even out against the edge and follow the notch on the border of the square).

Step two:
Continue working to the stringer, until you have set out the right number of notches. Use the carpenter's square to position the top cut on the stringer.

Step three:
Set the stringer on the lower floor by bolting it place with a piece of angling iron.

Step four:
Once the stringer is secured, cut the notches partway using a circular saw and finish the cuts with the handsaw.

Once you have one stringer finished, put it in place to make sure it is cut right, then use it as a guide to lay out your cuts on the other stringers.

Step five:
Measure the distance from the face of the riser to the edge of the notch cut, then pull the treads to breadth so they go 1" to 1-1/8" beyond the edge of the notch. If you're using two boards side by side as treads, rip half the dimension from either plank so both will be the same width. Cut the treads to length and nail them to the stringer with 16d galvanized nails.

The square root of the result yields you the required stringer length; round up to the nearest standard lumber length, then multiply by the number of stringers you'll require.


Tips and Warnings
Local building codes determine the breadth and slope of a staircase, as well as how the assembly is supported and braced, how the landing is made and whether railings are required.

Ensure that you check with local construction agencies to ensure that you have the required licences and are in compliance with all codes.

About the Author:
Please visit these links for more information on : How to Build Deck Stairs and How to Build Deck Stairs.



Article Originally Published On: http://www.articlesnatch.com


Tags: , ,

|

Loading...
Related....
Videos...

Recent Home-Improvement Articles

Comments

Still can't find what you are looking for? Search for it!

Loading

Site Navigation:

Copyright 2005-2011 ArticleSnatch, LLC - All Rights Reserved.
Privacy Policy | Terms of Service.