5 Reasons Why Aluminium Windows Are Losing Out To Grp Fibreglass

5 Reasons Why Aluminium Windows Are Losing Out To Grp Fibreglass

By:


Major breakthroughs in technology are rare but just occasionally a vastly improved new development appears which rewrites the rule-book and starts a new era in the life of that product or market.

Examples would be steel hulled ships instead of timber in the early 20th Century or the jet engine instead of propeller driven in the 1950's. More modest examples would be music cassettes replacing gramophone records in the 1970's, to be replaced themselves by CD's in the 1990's. Technology is unstoppable!

The first Plastics were developed in early 1900's and by World War 2 had been blended with glass fibres for astonishing strength and lightness. They were moulded into hulls for motor torpedo boats (MTBs), which were hugely effective and reached speeds above 40 mph. Impossible with the dead weight of steel hulls.
The same technology is still used today for RNLI Lifeboats to give maximum strength, lightness and speed. Perhaps surprisingly, the critically important nose cone on NASAs Space Shuttle comes from the same basic material.
These incredibly strong and durable composite compounds are Fibre Reinforced Polymers (FRPs) and until 1990's could only be produced manually in a mould (hand laid) or in a high pressure flat press to make sheets for, say, high performance composite door skins.

Around the same time, Aluminium was first created and widelt used in aircraft design and for building products like windows, curtain walling, display equipment, etc. The lesser demanding window applications for housing that generally require smaller windows than offices were subsequently replaced by thermoplastic PVC but this material does not have the inherent strength to challenge aluminium in larger and more demanding applications.
Thus PVC windows grew to dominate the housing market, whilst aluminium became the dominant supplier to the non-housing commercial market.
This continued for 30 years, until now.

Two important events occurred around the turn of the century to change this balance - namely, a) Climate Change and b) The development of 'Pultrusion', a continuous manufacturing process for FRP.

a) Climate Change - Gradual recognition of the causes and consequences of Climate Change has led to a succession of new legislation to reduce carbon emissions through better insulation of buildings and by developing more sustainable building practices and materials.
This has caused many specifiers to become dissatisfied with their historically traditional materials - and who are now seeking a more benign and longer lasting alternative.

Particular aspects causing dissatisfaction (confirmed by Greenpeace and Good Homes Alliance) are -
* Human toxicity and greenhouse gases from PVCU
* Tropical rainforest destruction and continuous maintenance of Timber
* High embodied energy and poor insulation properties of Aluminium.

Clients and specifiers, now, are increasingly demanding higher sustainability standards through increased levels of performance under BREEAM and Code for Sustainable Homes. Carbon neutral construction is also being mooted.
One of the single most important criteria in these higher standards is 'thermal insulation'. 47% of the entire carbon emissions from UK comes from fossil fuel replacement of the heat lost from all buildings.
Windows are one of the weakest points of insulation in all buildings, accounting for over 25% of that heat loss, a significant proportion of the total UK carbon footprint.
The weakest point in the insulation performance of a window is not the glass - but the frame that holds it.

b) Pultrusion - Enabling GRP to be made commercially in long continuous lengths for window profiles was a significant breakthrough in Plastics development in the 1980/90's in North America, which was introduced to UK in early 2000s. Pultrusion enabled window profiles to be made just like Aluminium or PVC but requiring no metal reinforcement for strength.
For the first time the advantages of FRP Fibreglass could be brought to bear on this specific product sector at the very time that it was coming under serious review.

The Consequences: Aluminium is unable to achieve U values below about 1.8, whilst far lower (1.2) is now being requested more and more by those striving for higher results under B.R.E.E.A.M. This is due to the very low insulation abilities of Aluminium (ironically, it is an excellent conductor), as well as to its notoriously high embodied energy from the high temperature manufacturing process. Also, it is recognised that aluminium is susceptible to a marine salt/sea spray environment which corrodes exposed aluminium. Powder coating reduces this effect until scratched or damaged but which cannot then be successfully repaired. Therefore the estimated service life is only 20 - 25 years.

Architects are now, therefore, seeking a more sustainable, longer lasting, better insulating alternative.

Whereas GRP Fibreglass as a material has consistently lower U values; is impervious to the weather and salt/sea spray; is stronger than steel; will not deform like aluminium; requires no maintenance; can be repaired and repainted if necessary; is 23% recycled; can be recycled on disposal; has pleasing slender sightlines; comes in any RAL colour and is similarly priced to aluminium whilst providing far better value and peace of mind for the client.

In summary:-
* Service life: 50 - 75 years is double that of any other low maintenance material.
* Thermal efficiency: U values of 0.9 are possible which is half that of aluminium.
* Strength: Twice the strength to weight ratio of steel, cannot deform like aluminium.
* Maintenance: No maintenance or protection is necessary the colour is applied for appearance only.
* Sustainability: Achieves a potential 3½ extra credits in any B.R.E.E.A.M assessment.

The final indicator as to the new supremacy of FRP composites over aluminium is in the Aeronautical Industry, where aluminium has previously dominated for 60 years.
Breaking with this tradition for the first time, the new Boeing 787 'Dream-liner' uses FRP nano-composites for 94% of the wings and fuselage. This provides reduced weight, therefore better fuel economy and lower carbon emissions, plus improved strength and durability, according to Russell Maquire, Technical Vice President, Boeing Company Inc.

Now who would argue with that?!

About the Author:
Chris Dixon has spent over 25 years successfully pioneering GRP building products and for 20 years was MD of Lindman, the original GRP composite door. Chris is now a freelance Business Consultant working with Pultec Ltd, UK market leader of GRP Windows.
Find out more about this new material at =>http://www.pultec.co.uk
Chris can be contacted at - cjd_home@hotmail.com



Article Originally Published On: http://www.articlesnatch.com


Tags: , , , , , , , , ,

|

Loading...
Related....
Videos...

Recent Business Articles

Comments

Still can't find what you are looking for? Search for it!

Loading

Site Navigation:

Copyright 2005-2011 ArticleSnatch, LLC - All Rights Reserved.
Privacy Policy | Terms of Service.